3 Setup Screens
MITSUBISHI CNC
I - 142
(Note 1) The measurement values are not written if the cursor is in a position other than "Length" or "Radius".
(Note 2) The axis returns and stops after contacting the sensor, but be careful not to move the axis after that. If the
axis moves after contacting the sensor, the distance that was actually moved will be added to the
measurement values counter, and the skip position will not be held.
Carrying out tool length measurement
(1)
Turn ON the measurement switch.
The message "On mea 0" appears.
Refer to the PLC Interface Manual for details on
measurement switch signals.
(2)
Press the [T-leng measure] menu.
The menu is highlighted, and the tool length measurement
starts. The measurement values are displayed in "Meas value"
during the measurement.
The menu [T-leng measure] is highlighted as a default after the
power is turned ON.
(3)
Contact the measurement tool against the sensor,
using manual feed and manual handle feed. Stop the
feed when the tool contacts the sensor.
When the measurement tool contacts the sensor, the skip
position displayed in the measurement values counter.
(4)
The cursor moves to the offset No. that sets the
measurement results.
The cursor appears.
[Offset No.] 12 [INPUT]
The cursor display position differs depending on the
measurement mode.
Tool length measurement mode:
Length dimension
Tool radius measurement mode:
Radius dimension
(5)
Press the [Offset write] menu.
The measurement values are written as a tool compensation
amount.
The wear amount is cleared to "0" for the tool compensation
type II.
(6)
Turn OFF the measurement switch to finish
measuring.
The message "On mea 0" disappears.
Summary of Contents for E70 Series
