E70 Series Instruction Manual
6.23 Spindle Orientation
II - 57
(2) Time constant
The parameter "#3115 sp2_t1" to "#3118 sp2_t4" (Time constant in orientation/position loop reference position return)
are used as the time constant of orientation/position loop reference position return. The parameter "#3124 tret_t" (Turret
indexing time constant) is used at the turret indexing. Set the relation to the parameters "#3101 sp_t 1" to "#3104 sp_t 4"
(Time constant for spindle rotation with S command) as follows.
If the orientation is commanded when the spindle has been stopping, usually the spindle rotates to orientation position
using the position loop gain set in the parameter "#13002 SP002(PGN)" (Position loop gain interpolation mode).
By setting the parameter "#3106 zrn_typ/bitE" (Interpolation mode selection in orientation), if the orientation is
commanded when the spindle has been stopping, the spindle rotates to orientation position using the parameter "#13001
SP001(PGV)" (Position loop gain Non-interpolation mode). When the parameter "#3106 zrn_typ/bitF" (Spindle zero point
detection with contactless switch) or the parameter "#3121 tret" (Turret indexing) is set, the parameter "#3106 zrn_typ/
bitE" (Interpolation mode selection in orientation) setting is not enabled.
Gain
sp2_t(n)
Time (ms)
tret_t
sp_t(n)
slimt
S
pindle speed(r/min)
Summary of Contents for E70 Series
