E70 Series Instruction Manual
Appendix 6.1 Operation Errors (M)
IV - 43
M01 3D manual feed coord sys err 0231
Details
- More than one of the three bits for selecting hypothetical coordinate system was turned ON.
- Hypothetical coordinate system was selected while the manual feed for 5-axis machining was
invalidated by the parameter setting.
Remedy
- Check the sequence program.
- Enable 3-dimensional tool radius compensation (set the parameter "#7912 NO_MANUAL" to "0").
M01 Illegal op in 3D tool R comp 0232
Details
An illegal operation (such as manual interrupt) was attempted during 3-dimensional tool radius
compensation (tool vertical direction compensation).
Remedy
- Operations such as manual interrupt are disabled while 3-dimensional tool radius compensation (tool
vertical direction compensation) is being performed.
M01 Machining surface operation disabled 0250
Details
Machining surface operation (selection, indexing or cancel) was attempted while the operation is
disabled.
Remedy
- Cancel the other modes so that the inclined surface machining command (G68.2), tool axis direction
control (G53.1) and the inclined surface machining cancel command (G69) can be issued.
- Wait until the axes stop completely (until the smoothing for all axes reaches zero).
- Perform operation search for machining programs.
M01 Axs travel n/a in manual index 0251
Details
Moving a rotary axis was attempted during manual machining surface indexing, when a manual
operation mode other than handle mode was selected.
Remedy
- Change the operation mode to a handle mode before carrying out the manual surface indexing.
M01 Tool length compensation amt 0 0252
Details
The tool length compensation amount for performing the R-Navi indexing type 2 is 0.
Remedy
- Set the tool length compensation amount for performing the indexing type 2 to a value other than 0.
M01 Feat coord ill w/ multi-handle 0253
Details
Manual feed feature coordinate system was selected while two or more handles were ON.
Remedy
- Manual feed on a feature coordinate system is disabled while two or more handles are enabled (*).
- Press [Manual coord] and select the machine coordinate system.
- Reduce the number of enabled handles (*) to one.
(*) An enabled handle means the handle for which “Nth handle valid” signal (HSnS) is ON.
Summary of Contents for E70 Series
