Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 122
P161 No spec: 3D tool R comp
Details
3-dimensional tool radius compensation (tool vertical direction compensation) is not included in the
specifications.
Remedy
- Check the specifications.
P162 Disable Cmd in 3D tool R comp
Details
A command (G or T command, etc) was issued during 3-dimensional tool radius compensation (tool
vertical direction compensation), although it is disabled during the compensation.
Remedy
- Cancel 3-dimensional tool radius compensation (tool vertical direction compensation).
P163 3D tool R comp is disabled
Details
3-dimensional tool radius compensation (tool vertical direction compensation)
Remedy
- Cancel the mode that disables the command.
P170 No offset number
Details
- No offset No. (DOO, TOO or HOO) command was given when the radius compensation (G41, G42,
G43 or G46) command was issued. Otherwise, the offset No. is larger than the number of sets in the
specifications.
- When setting the L system tool life management II, the tool group management program was
executed with the tool life management disabled.
Remedy
- Add the offset No. command to the compensation command block.
- Check the number of sets for the tool compensation Nos. and correct the offset No. command to be
within the number of sets.
- When setting the L system tool life management II ("#1096 T_Ltyp"="2"), enable the tool life
management ("#1103 T_Life"="1") to execute a tool group management program.
P171 No spec:Comp input by prog G10
Details
Compensation data input by program (G10) was commanded though it is out of specifications.
Remedy
- Check the specifications.
P172 G10 L number error
Details
An address of G10 command is not correct.
Remedy
- Correct the address L No. of the G10 command.
P173 G10 P number error
Details
The offset No. at the G10 command is not within the permitted number of sets in the specifications.
Remedy
- Check the number of sets for the tool compensation Nos. and correct the address P designation to
be within the number of sets.
P174 No spec:Comp input by prog G11
Details
Compensation data input by program cancel (G11) was commanded though there is no specification of
compensation data input by program.
Remedy
- Check the specifications.
Summary of Contents for E70 Series
