E70 Series Instruction Manual
Appendix 6.5 System Alarms (Z)
IV - 93
Z34 DeviceNet error
Details
Any of the following errors has occurred in the DeviceNet unit.
- Master function error (X03 is ON)
- Slave function error (X08 is ON)
- Message communication error (X05 is ON)
If the errors have occurred in more than one unit, the error No. of the unit with the smallest slot No. is
displayed.
If the master function, slave function and message communication errors have occurred at the same
time, the error is displayed in the following priority order.
1. Master function error
2. Slave function error
3. Message communication error
Remedy
- Select the [Ext. PLC link control] menu on the maintenance screen to open the unit confirmation
screen, and check the unit in error and details to cancel the error.
For the details of the DeviceNet unit errors, refer to "External PLC Link II (Bus connection) MELSEC-
Q Series Appendix 2 (DeviceNet)"BNP-C3039-276 (Appendix 2).
Z35 Direct Socket connection error 0001
Details
- Connection has failed.
- Five or more clients attempted a connection.
Remedy
- Check the connection of the network cables, and check for broken wires and a failure of the network
connection devices such as hub.
- When using the Direct Socket communication I/F, connect up to four clients.
Z35 Direct Socket receive error
0002
Details
- Receiving data from a client has failed.
Remedy
- Check the connection of the network cables, and check for broken wires and a failure of the network
connection devices such as hub.
Z35 Direct Socket send error 0003
Details
- Sending data to a client has failed.
Remedy
- Check the connection of the network cables, and check for broken wires and a failure of the network
connection devices such as hub.
Z35 Direct Socket timeout error 0004
Details
There was no response from client computers, and a timeout error occurred.
Remedy
Check the connection of the network cables, and check for broken wires and a failure of the network
connection devices such as hub.
Z35 Direct Socket comm OFF 0005
Details
The direct Socket communication I/F is OFF.
Remedy
Check the parameter "#11051 Direct Socket OFF".
Summary of Contents for E70 Series
