E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 121
P155 Fixed cyc exec during compen
Details
A fixed cycle command has been issued in the radius compensation mode.
Remedy
- Issue a radius compensation cancel command (G40) to cancel the radius compensation mode that
has been applied since the fixed cycle command was issued.
P156 R compen direction not defined
Details
A shift vector with undefined compensation direction was found at the start of G46 nose R
compensation.
Remedy
- Change the vector to that which has the defined compensation direction.
- Change the tool to that which has a different tip point No.
P157 R compen direction changed
Details
During G46 nose R compensation, the compensation direction is reversed.
Remedy
- Change the G command to that which allows the reversed compensation direction (G00, G28, G30,
G33, or G53).
- Change the tool to that which has a different tip point No.
- Enable "#8106 G46 NO REV-ERR".
P158 Illegal tip point
Details
An illegal tip point No. (other than 1 to 8) was found during G46 nose R compensation.
Remedy
- Correct the tip point No.
P159 C-CMP REMAINS
Details
One of the followings was commanded while the compensation has not been canceled (the
compensation amount remained).
(1) Automatic tool nose R compensation (G143)
(2) Radius compensation (G145)
(3) Plane selection (G17 to G19)
(4) Skip (G31 or G31.1/G31.2/G31.3)
(5) Fixed cycle for drilling (G81 to G89)
(6) Compound type fixed cycle II (G74 to G76)
Remedy
- Cancel the compensation (with compensation amount "0") before commanding.
- Command the G00 move block before the block with a command among (1) to (6).
P160 G53 CMP. ERR
Details
- G53 was commanded during nose R compensation (by G41/G42/G46).
- G53 was commanded to the block where the nose R compensation mode is changed (with G40/
G41/G42/G46).
- G53 was commanded while nose R compensation amount has not been cleared.
Remedy
- Correct the program.
- When issuing G53 after G40 command, move the compensation plane axis by G00/G01/G02/G03
command before issuing G53.
Summary of Contents for E70 Series
