Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 80
Appendix 6.4 MCP Alarms (Y)
Y02 System alm: Process time over 0050
Details
System alarm: Process time is over.
Remedy
The software or hardware may be damaged.
Contact the service center.
(Note) When two or more "Y02 System alarms" occur at the same time, only the alarm which has
occurred first is displayed.
Y02 SV commu er: CRC error 1 0051 0000
Details
A communication error has occurred between controller and drive unit.
Remedy
- Take measures against noise.
- Check for any failure of the communication cable connectors between controller and drive unit or
between two drive units.
- Check for any failure of the communication cables between controller and drive unit or between two
drive units.
- A drive unit may be faulty. Take a note of the 7-segment LED contents of each drive unit and contact
the Service Center.
- Update the drive unit software version.
(Note) When two or more "Y02 System alarms" occur at the same time, only the alarm which has
occurred first is displayed.
Y02 SV commu er: CRC error 2 0051 0001
Details
A communication error has occurred between controller and drive unit.
Remedy
- Take measures against noise.
- Check for any failure of the communication cable connectors between controller and drive unit or
between two drive units.
- Check for any failure of the communication cables between controller and drive unit or between two
drive units.
- A drive unit may be faulty. Take a note of the 7-segment LED contents of each drive unit and contact
the Service Center.
- Update the drive unit software version.
(Note) When two or more "Y02 System alarms" occur at the same time, only the alarm which has
occurred first is displayed.
Y02 SV commu er: Recv timing err 0051 0002
Details
A communication error has occurred between controller and drive unit.
Remedy
- Take measures against noise.
- Check for any failure of the communication cable connectors between controller and drive unit or
between two drive units.
- Check for any failure of the communication cables between controller and drive unit or between two
drive units.
- A drive unit may be faulty. Take a note of the 7-segment LED contents of each drive unit and contact
the Service Center.
- Update the drive unit software version.
(Note) When two or more "Y02 System alarms" occur at the same time, only the alarm which has
occurred first is displayed.
Summary of Contents for E70 Series
