E70 Series Instruction Manual
6.11 Mirror Image
II - 27
6.11 Mirror Image
When cutting a shape having bilateral symmetry, this function can be used to machine either the right or left side of the
shape from the program for the other side, thus saving programming time. When cutting a shape having upper and lower
symmetry, this function can be used to machine either the upper or lower side of the shape from the program for the
other side.
The mirror image function is effective in this case.
For example, when there is a program for machining the left side of the shape shown in the following drawing, a
symmetrical shape to the left side shape can be machined on the right side by applying the mirror image function and
running the same program.
Be sure the machining program starts and finishes at the mirror center.
Mirror image includes external input mirror image, parameter setting mirror image, programmable mirror image, etc. Only
program mirror image function can be used in E70 series. (M system only)
Refer to the Programming Manual for information on programmable mirror image.
Y
X
Shape when the X axis mirror image is turned
ON and the left side machining program is run.
Original shape (program)
Mirror axis
Position where the mirror image is turned ON.
Basic machine
coordinate system
Summary of Contents for E70 Series
