Appendix 8 User Parameters
MITSUBISHI CNC
IV - 174
【
#1569
】
SfiltG0 G00 soft acceleration/deceleration filter
Set the filter time constant for smoothly changing the acceleration rate for the rapid traverse
acceleration/deceleration in pre-interpolation acceleration/deceleration.
---Setting range---
0 to 200 (ms)
【
#1570
】
Sfilt2 Soft acceleration/deceleration filter 2
Set the filter time constant for smoothly changing the acceleration rate in pre-interpolation
acceleration/deceleration.
This will be disabled when "0" or "1" is set.
---Setting range---
0 to 200 (ms)
Notch frequency Hz
Displays the notch frequency(Hz) for the S-pattern filter set in "#1570 Sfilt2 (Soft acceleration/
deceleration filter 2)".
【
#1571
】
SSSdis SSS control adjustment coefficient fixed value selection
Fix the shape recognition range for SSS control.
【
#1926(PR)
】
Global IP address IP address
Set the main CPU's IP address.
Set the NC IP address seen from an external source.
【
#1927(PR)
】
Global Subnet mask Subnet mask
Set the subnet mask for the IP address.
【
#1928(PR)
】
Global Gateway Gateway
Set the IP address for the gateway.
【
#1934(PR)
】
Local IP address
Set the HMI side CPU's IP address.
(Note) This parameter is valid only for M700/M700VW Series.
【
#1935(PR)
】
Local Subnet mask
Set the HMI side CPU's subnet mask.
(Note) This parameter is valid only for M700/M700VW Series.
【
#2001
】
rapid Rapid traverse rate
Set the rapid traverse feedrate for each axis.
(Note) The maximum value to be set depends on the machine specifications.
---Setting range---
1 to 1000000 (mm/min)
【
#2002
】
clamp Cutting feedrate for clamp function
Set the maximum cutting feedrate for each axis.
Even if the feedrate in G01 exceeds this value, the clamp will be applied at this feedrate.
---Setting range---
1 to 1000000 (mm/min)
Summary of Contents for E70 Series
