E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 143
P954 Inclined face command error
Details
The address to issue the inclined surface machining command is incorrect.
Remedy
- Check the program.
P955 Inclined face coord illegal
Details
Impossible to define an inclined surface with the values you specified.
Remedy
- Check the program.
P956 G68.2P10 surface not defined
Details
The coordinate system for the machining surface selected with G68.2P10 has not been defined.
Remedy
- Set the machining surface so that the coordinate system can be defined.
P957 Tool axis dir ctrl cmp amt 0
Details
When the tool axis direction control type 2 (G53.6) was commanded, a tool length offset No. whose
compensation amount is 0 was commanded.
Remedy
- Correct the program. Set the tool length compensation amount, or command a tool length offset No.
whose compensation amount is not 0.
P960 No spec: Direct command mode
Details
G05 P4 was commanded while direct command mode option is OFF.
Remedy
- Check the specifications.
P961 Invalid during dir cmnd mode
Details
- A G code other than G05 P0 was commanded in direct command mode.
- A sequence No. command, F code command, MSTB command or variable command was issued.
- A corner chamfering command or corner R command was issued.
- A travel command was issued to an axis that had not been command in the G05 P4 block.
Remedy
- Check the program.
P962 Dir cmnd mode cmnd invalid
Details
G05 P4 was commanded in a modal where direct command mode is not available.
Remedy
- Check the program.
P963 Illegal direct cmnd mode cmnd
Details
The commanded coordinate value was beyond the maximum travel distance in direct command mode.
Remedy
- Correct the coordinate value in direct command mode.
Summary of Contents for E70 Series
