E70 Series Instruction Manual
IV - 183
【
#8071
】
3-D CMP (for M system only)
Set the value of the denominator constants for 3-dimensional tool radius compensation.
Set the value of "p" in the following formula.
Vx = i x r/p, Vy = j x r/p, Vz = k x r/p
Vx, Vy, Vz : X, Y, and Z axes or vectors of horizontal axes
i, j, k : Program command value
r : Offset
p =
√
(i
2
+ j
2
+ k
2
) when the set value is "0".
---Setting range---
0 to 99999.999
【
#8072
】
SCALING P (for M system only)
Set the scale factor for reduction or magnification in the machining program specified by G50 or G51
command.
This parameter will be valid when the program specifies no scale factor.
---Setting range---
-99.999999 to 99.999999
【
#8075
】
SpiralEndErr (for M system only)
Set the tolerable error range (absolute value) when the end point position, commanded by the spiral
or conical interpolation command with the command format type 2, differs from the end point position
obtained from the speed and increment/decrement amount.
---Setting range---
0 to 99999.999 (mm)
【
#8078
】
Screen Saver Timer
Set the period of time before turn-OFF of the display unit backlight.
When "0" is set, the backlight is not turned OFF.
---Setting range---
0 to 60 (min)
0: The backlight is not turned OFF
【
#8081
】
Gcode Rotat (for L system only)
Set the rotation angle for the program coordinate rotation command.
This parameter is enabled when "1" is set in "#1270 ext06/bit5 (Coordinate rotation angle without
command)".
This parameter is set as absolute value command regardless of the "#8082 G68.1 R INC" setting. If
the rotation angle is designated by an address R in G68.1 command, the designation by program will
be applied.
---Setting range---
-360.000 to +360.000 (°)
【
#8082
】
G68.1 R INC (for L system only)
Select absolute or increment command to use for the rotation angle command R at L-system
coordinate rotation.
0: Use absolute value command in G90 modal, incremental value command in G91 modal
1: Always use incremental value command
(Note) If G91 does not exist in the G code system, the command type is decided by this parameter
only.
【
#8083
】
G83S modeM (for M system only)
Set the M command code for changing to the small diameter deep hole drilling cycle mode.
---Setting range---
1 to 99999999
Summary of Contents for E70 Series
