Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 60
Appendix 6.3 Servo/Spindle Alarms (S)
Appendix 6.3.1 Servo Errors (S01/S03/S04)
Servo alarm is displayed in the following format.
Error No. consists of four digits (0010 to). Servo alarms are explained in ascending order of the error No. The four digits
on the left part of each alarm indicate the error No.
(Note) For the details of servo alarms, refer to your drive unit's instruction manual.
Drive unit alarms
0010 Insufficient voltage
Details
A drop of bus voltage was detected in main circuit.
- Servo stop method: Dynamic stop
- Spindle stop method: Coast to a stop
0011 Axis selection error
Details
The axis selection rotary switch has been incorrectly set.
- Servo stop method: Initial error
- Spindle stop method: Initial error
0012 Memory error 1
Details
A hardware error was detected during the power ON self-check.
- Servo stop method: Initial error
- Spindle stop method: Initial error
0013 Software processing error 1
Details
An error was detected for the software execution state.
- Servo stop method: Dynamic stop
- Spindle stop method: Coast to a stop
0014 Software processing error 2
Details
The current processing processor does not operate correctly.
- Servo stop method: Dynamic stop
- Spindle stop method: Coast to a stop
Axis name
Servo : Axis name
Spindle : "S", "T", "M", "N", "P", "Q", "R"
Error No.
Reset method
Message
Alarm class
Alarm class
Message
Reset method
Resetting methods
S01
Servo alarm
PR
After removing the cause of the alarm, reset the alarm by turning the
NC power ON again.
S03
Servo alarm
NR
After removing the cause of the alarm, reset the alarm by inputting
the NC RESET key.
S04
Servo alarm
AR
After removing the cause of the alarm, reset the alarm by turning the
drive unit power ON again.
S
S
Summary of Contents for E70 Series
