6 Operation Panel Switch Functions
MITSUBISHI CNC
II - 28
6.12 Error Detect
For positioning (G00), machine deceleration check is made before next block movement is started. For cutting (G01,
G02, or G03), the next block is started before the machine reaches the movement command end point. Thus, the corner
part is slightly rounded.
To prevent rounded corners, turn ON the error detect signal. This will cause the machine to decelerate until the
remaining distance falls below the value of the parameter. The next block command is stopped during this time.
This function is equivalent to G09 in the program.
The parameter that is used by the error detect switch and the G09 command for determining the remaining distance after
deceleration for moving to the next command can be set with the setting and display unit.
6.13 Follow-up Function
The follow-up function monitors machine motion in the emergency stop state and reflects it in the current position and
workpiece coordinates. Thus, the work program can be continued without re-executing a reference position return after
emergency stop.
6.14 Axis Removal
When the machine receives the axis removal signal, that axis no longer becomes the controlled axis. Accordingly, the
alarm related with axis, such as the stroke end axis, and the servo alarms (excessive errors, lack of signal, drive alarm,
etc.) will be ignored. At the same time, the axis will become interlocked.
(Note)This cannot be used for the absolute position detector specification axis.
X axis command
Y axis command
Y axis command
Error detect off
Error detect on
Summary of Contents for E70 Series
