E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 125
P201 Program error (MRC)
Details
- The subprogram, called with a compound type fixed cycle for turning machining I command, has at
least one of the following commands: reference position return command (G27, G28, G29, G30);
thread cutting (G33, G34); fixed cycle skip-function (G31, G31.n).
- An arc command was found in the first movement block of the finished shape program in compound
type fixed cycle for turning machining I.
Remedy
- Delete G27, G28, G29, G30, G31, G33, G34, and fixed cycle G codes from the subprogram called
with the compound type fixed cycle for turning machining I commands (G70 to G73).
- Delete G02 and G03 from the first movement block of the finished shape program in compound type
fixed cycle for turning machining I.
P202 Block over (MRC)
Details
The number of blocks in the shape program of the compound type fixed cycle for turning machining I is
over 50 or 200 (the maximum number differs according to the model).
Remedy
- Set a 50/200 or less value for the number of blocks in the shape program called by the compound
type fixed cycle for turning machining I commands (G70 to G73). (The maximum number differs
according to the model).
P203 D cmnd figure error (MRC)
Details
A proper shape will not obtained by executing the shape program for the compound type fixed cycle for
turning machining I (G70 to G73).
Remedy
- Correct the shape program for the compound type fixed cycle for turning machining I (G70 to G73).
P204 E cmnd fixed cycle error
Details
A command value of the compound type fixed cycle for turning machining (G70 to G76) is illegal.
Remedy
- Correct the command value of the compound type fixed cycle for turning machining (G70 to G76).
P210 No spec: Pattern cycle
Details
A compound type fixed cycle for turning machining II (G74 to G76) command was commanded though
it is out of specifications.
Remedy
- Check the specifications.
P220 No spec: Special fixed cycle
Details
There are no special fixed cycle specifications.
Remedy
- Check the specifications.
P221 No. of special fixed holes = 0
Details
"0" has been specified for the number of holes in special fixed cycle mode.
Remedy
- Correct the program.
P222 G36 angle error
Details
A G36 command specifies "0" for angle intervals.
Remedy
- Correct the program.
Summary of Contents for E70 Series
