E70 Series Instruction Manual
4.3 Program Check (2D)
I - 255
(1) Auto graphic is executed only for the 1-plane display mode. [Auto Graphic] menu cannot be selected for the other
modes. Auto graphic mode always remains as it is in the 1-plane display mode.
(2) Once the auto graphic mode is set, it is retained after the power is turned ON again.
(3) Auto graphic cannot be set with a trace function.
(4) Even M00 or M01 command does not cause "PROGRAM STOP".
(5) If a program which contains M99 command is selected, auto adjustment of the scale will be executed repeatedly
and the adjustment will not be completed with the "Executing auto scale" message blinking. Do not select a
program which contains M99. Execute check reset when it happens.
(6) When a large capacity program is selected, it may take time to perform the auto graphic.
(7) If a displayed position for a figure is changed due to change in display range, a graphic drawing will not be
performed automatically.
Auto graphic drawing is performed only when the figure is enlarged or reduced.
(8) If a check search is performed on a file which went through an auto-adjustment of the scale, only graphic drawing
will be performed as long as there is no changes in "a path and a file name (including a device)", "the date of
updating", or display mode (XY/YZ/XZ.. etc).
However, a maximum of 12 files to which an auto-adjustment of the scale has been executed, can be memorized.
(9) Automatic adjustment of the scale will be interrupted if one of the following operations is taken:
- Press the [Check reset] menu;
- Press the [Auto Graphic] menu;
- The screen is changed to other than [2D check];
- A program error occurs.
Precautions
Summary of Contents for E70 Series
