E70 Series Instruction Manual
IV - 195
【
#8706
】
FEED
Set the feedrate when contacting again.
---Setting range---
1 to 60000 (mm/min)
【
#8707
】
Skip past amout (H)
Set the difference (horizontal axis direction) between the skip read value and actual skip position.
---Setting range---
-99999.999 to 99999.999 (mm)
【
#8708
】
Skip past amout (V)
Set the difference (vertical axis direction) between the skip read value and actual skip position.
---Setting range---
-99999.999 to 99999.999 (mm)
【
#8709
】
EXT work sign rvs
Reverse the sign of external workpiece coordinate.
Select when using the external workpiece coordinate system with Z shift.
0: External workpiece offset without sign reversal
1: External workpiece offset with sign reversal
【
#8710
】
EXT work ofs invld
Set whether to enable external workpiece offset subtraction when setting the workpiece coordinate
offset.
0: Not subtract the external workpiece offset. (Conventional specification)
1: Subtract the external workpiece offset.
【
#8711
】
TLM L meas axis
Set the tool length measurement axis.
Set the "#1022 axname2" axis name.
---Setting range---
Axis name
(Note) If the axis name is illegal or not set, the 3rd axis name will be set as default.
【
#8712
】
TLM D meas axis
Set the tool diameter measurement axis.
Set the "#1022 axname2" axis name.
---Setting range---
Axis name
(Note) If the axis name is illegal or not set, the 1st axis name will be set as default.
【
#8713
】
Skip coord. Switch (For M system only)
Select the coordinate system for reading skip coordinate value.
Select whether to read the skip coordinate in the workpiece coordinate system or in the feature
coordinate system during inclined surface machining command.
Select whether to read the skip coordinate in the workpiece coordinate system or in the workpiece
installation coordinate system during workpiece installation error compensation.
0: Workpiece coordinate system
1: Feature coordinate system/Workpiece installation coordinate system
【
#8714
】
Rethread lead axis
Specify the name of lead axis to use for thread recutting.
If a non-existent axis name is specified, the 1st axis of the part system serves as a lead axis for
thread recutting.
If the parameter #8714 (Rethread lead axis) is not set, Z is set as the parameter value at power ON.
---Setting range---
A, B, C, U, V, W, X, Y, Z
Summary of Contents for E70 Series
