E70 Series Instruction Manual
4.4 Program Input/Output
I - 287
In a file transfer with "#8936 Delete leading 0" set to "1", only when the file name of the transfer destination consists only
of numerical figures, the leading "0" is deleted when the file is transferred.
However, if the file name is out of the range between 1 and 99999999, the leading "0" is not deleted. This also applies to
MTB macros.
In the case of fixed cycles, regardless of the setting of "#8936 Delete leading 0", the name of the file to transfer must be
9 digits, and it must not start from "0". Attempting to create new file whose name does not satisfy the conditions above
will cause an error.
In a file comparison, even if "#8936 Delete leading 0" is set to "1", when comparing one separate file that contains one
program, "0" at the head of the program name is not deleted. Designating the file name is required.
However, in the case of serial/batch file, comparison is carried out with "0" at the head of the program name deleted.
(Example 1) One file has one program
(1) The file is transferred from the Memory card to memory.
When transferring to the memory, the following occurs.
The leading zero is deleted from the file name.
(2) In order to carry out comparison, change the file name of the transfer destination to "10".
(In a comparison of one separate file that has one program, as "0" at the head of the program name is not
deleted, if the file name remains "000010", it will be compared with the file "000010" of the transfer
destination.)
When transferring, or comparing files
A Dev: Memory card
Dir: /
File: 001000
B Dev: Memory
Dir: Program
File: 000010
Memory
10
(P001000)
:
%
A Dev: Memory card
Dir: /
File: 001000
B Dev: Memory
Dir: Program
File: 10
Summary of Contents for E70 Series
