E70 Series Instruction Manual
IV - 185
【
#8102
】
COLL. ALM OFF
Select the interference (bite) control to the workpiece from the tool diameter during tool radius
compensation and nose R compensation.
0: An alarm will be output and operation stops when an interference is judged.
1: Changes the path to avoid interference.
【
#8103
】
COLL. CHK OFF
Select the interference (bite) control to the workpiece from the tool diameter during tool radius
compensation and nose R compensation.
0: Performs interference check.
1: Does not perform interference check.
【
#8105
】
EDIT LOCK B
Select the edit lock for program Nos. 8000 to 9999 in the memory.
0: Enable the editing.
1: Prohibit the editing of above programs.
When "1" is set, the file cannot be opened.
【
#8106
】
G46 NO REV-ERR (for L system only)
Select the control for the compensation direction reversal in G46 (nose R compensation).
0: An alarm will be output and operation will stop when the compensation direction is reversed
(G41 -> G42' G42 -> G41).
1: An alarm won't occur when the compensation direction is reversed, and the current
compensation direction will be maintained.
【
#8107
】
R COMPENSATION
Select whether to move to the inside because of a delay in servo response to a command during arc
cutting mode.
0: Move to the inside, making the arc smaller than the command value.
1: Compensate the movement to the inside.
【
#8108
】
R COMP Select
Select the arc radius error compensation target.
0: Perform compensation over all axes.
1: Perform compensation axis by axis.
(Note) This parameter is effective only when "#8107 R COMPENSATION" is "1".
【
#8109
】
HOST LINK
Select whether to enable computer link B instead of the RS-232C port.
0: Disable (Enable normal RS-232C communication.)
1: Enable (Disable normal RS-232C communication.)
【
#8110
】
G71/G72 POCKET
Select whether to enable the pocket machining when there is a dimple (pocket) in the rough cutting
cycle (G71, G72) finishing program.
0: OFF
1: ON
【
#8111
】
Milling Radius
Select the diameter and radius of the linear axis for milling (cylindrical/pole coordinate) interpolation.
0: All axes radius command
1: Each axis setting (follows "#1019 dia")
(Note) This parameter is valid only in the milling (cylindrical/polar coordinate) interpolation mode.
【
#8112
】
DECIMAL PNT-P
Select whether to enable the decimal point command for G04 address P.
0: Disable
1: Enable
Summary of Contents for E70 Series
