E70 Series Instruction Manual
Appendix 6.1 Operation Errors (M)
IV - 49
M01 Cont ax superimpos II prm illg 1044
Details
The superimposition control request signal was turned
ON in any of the following cases.
- There is a mistake in the setting of the superimposition control base axis parameter (#2089 bsax_pl).
- Superimposition control is not available under the current parameter settings.
Remedy
- Correct the parameter.
M01 Intrf chck across sys: Set err 1050
Details
Setting of Interference check across part systems is incorrect.
Remedy
- Correct the setting of Interference check across part systems.
M01 Intrf chck across sys: Area AL 1051
Details
Interference is already occurring on the set interfering object.
Remedy
- Disable Interference check across part systems, move the axis to a position where the interfering
objects do not collide each other, and then restart Interference check across part systems.
M01 Intrf check across sys: Alarm 1052
Details
A command has been given that causes the interfering objects to collide each other.
Remedy
- Correct the program.
M01 Interfe chk 0pt return incomp 1053
Details
Interference check between part systems had started while zero point return of the part system set
interfering object has not completed.
Remedy
- Disable interference check between part system, and complete zero point return in the all part
systems set interfering object.
M01 Feed-forward control disabled 1060
Details
Feed-forward control was attempted while any of the following functions was active.
- Control axis superimposition I / II
- Control axis synchronization across part systems I / II
Remedy
- Turn OFF the feed-forward control request signal.
M01 Sp synchro phase calc illegal 1106
Details
Spindle synchronization phase alignment command was issued while the "phase shift calculation
request" signal was ON.
Remedy
- Correct the program.
- Correct the sequence program.
Summary of Contents for E70 Series
