E70 Series Instruction Manual
IV - 171
【
#1104
】
T_Com2 Tool command method 2
Select how to handle the tool command in the program when "#1103 T_Life" is set to "1".
0: Handle the command as group No.
1: Handle the command as tool No.
(Note) In the case of the tool life management III, the program tool command will be handled as the
tool No. regardless of the setting.
【
#1105
】
T_Sel2 Tool selection method 2
Select the tool selection method when "#1103 T_Life" is set to "1".
0: Select in order of registered No. from the tools used in the same group.
1: Select the tool with the longest remaining life from the tools used or unused in the same group.
【
#1106
】
Tcount Life management (for L system only)
Select the input method when address N is omitted in inputting the data (G10 L3 command) for tool
life management function II.
0: Time specified input
1: Number of times specified input
【
#1126
】
PB_G90 Playback G90
Select the method to command the playback travel amount in the playback editing.
0: Incremental value
1: Absolute value
【
#1128
】
RstVCI Clear variables by resetting
Select how to handle the common variables when resetting.
0: Common variables won't change after resetting.
1: The following common variables will be cleared by resetting:
#100 to #149 when 100 sets of variables are provided.
#100 to #199 when 200 sets or more of variables are provided.
【
#1129
】
PwrVCl Clear variables by power-ON
Select how to handle the common variables when the power is turned ON.
0: The common variables are in the same state as before turning the power OFF.
1: The following common variables will be cleared when the power is turned ON:
#100 to #149 when 100 sets of variables are provided.
#100 to #199 when 200 sets or more of variables are provided.
【
#1148
】
I_G611 Initial high precision
Set the high accuracy control mode for the modal state when the power is turned ON.
0: G64 (cutting mode) at power ON
1: G61.1 (high-accuracy control mode) at power ON
(Note) When the option of high-accuracy control in 2 part systems is enabled, it will be enabled in
both systems.
【
#1149
】
cireft Arc deceleration speed change
Select whether to decelerate at the arc entrance or exit.
0: Not decelerate
1: Decelerate
【
#1171
】
taprov Tap return override
Set the tap return override value for the synchronous tapping.
When "0" is set, it will be regarded as 100%.
---Setting range---
0 to 100 (%)
Summary of Contents for E70 Series
