E70 Series Instruction Manual
Appendix 6.1 Operation Errors (M)
IV - 47
M01 Re-thread cutting impossible 1027
Details
A command not compatible with thread recutting was issued.
Remedy
- The command that was issued is not compatible with thread recutting. Execute the command after
disabling thread recutting.
M01 Re-thread cutting data illegal 1028
Details
The lead axis and spindle for thread recutting are different from those set in the parameter.
Remedy
- Correct the parameter.
M01 Synchronization mismatch 1030
Details
Different M codes were each commanded as synchronization M code in each of the two part systems.
Synchronization with the "!" code was commanded in another part system during M code
synchronization.
Synchronization with the M code was commanded in another part system during synchronization with
the "!" code.
Remedy
- Correct the program so that the M codes match.
- Correct the program so that the same synchronization codes are commanded.
M01 Multiple C axes select invalid 1031
Details
The "C axis selection" signal has been changed when the multiple C axes selection is not available.
The selected axis by the "C axis selection" signal cannot be controlled for the multiple C axes
selection.
Remedy
- Correct the parameter settings and program.
M01 Tap retract Sp select illegal 1032
Details
Tap retract has been executed with a different spindle selected. Cutting feed is in wait state until
synchronization is completed.
Remedy
- Select the spindle for which tap cycle was halted before turning ON the "tap retract" signal.
M01 Sp-Sp polygon cut interlock 1033
Details
Cutting feed is in wait state until synchronization is completed.
Remedy
- Wait for the synchronization to end.
M01 Mixed sync ctrl prmtr illegal 1034
Details
There is a mistake in the settings of mixed control axis parameters (crsax [1] to [8]).
Mixed control was attempted within one and the same part system.
Any of the parameter settings is disabling mixed control.
Remedy
- Correct the parameter settings for the mixed control (cross axis control).
Summary of Contents for E70 Series
