Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 56
T01 In interference check alarm 0173
Details
Cycle start is disabled during interference check alarm.
Remedy
- Cancel the interference check alarm before pressing the cycle start.
T01 Cycle start prohibit 0180
Details
Automatic start became disabled while servo auto turning is enabled.
Remedy
- Set "#1164 ATS" to "0" when the servo auto turning is not executed.
T01 Cycle st. prohibit (in search) 0181
Details
Cycle start is disabled because operation search is being executed.
Remedy
- Press the cycle start button after the operation search is completed.
T01 Cycle start prohibit 0190
Details
Automatic start is not possible because the setting of setup parameters is enabled.
Remedy
- Refer to the manual issued by the machine tool builder.
T01 Cycle start prohibit 0191
Details
Automatic start was attempted while a file was being deleted/written.
Remedy
- Wait for the file to be deleted/written and then execute the automatic start.
T01 Cycle st. prohibit (Term exp'd) 0193
Details
Automatic start is not possible because the valid term has been expired.
Remedy
- Obtain a decryption code from the machine tool builder and input it in the NC, then turn the power
ON again.
T02 H/W stroke end axis exists 0201
Details
An axis is at the stroke end.
Remedy
- Manually move the axis away from the stroke end limit switch.
- Correct the machining program.
T02 S/W stroke end axis exists 0202
Details
An axis is at the stored stroke limit.
Remedy
- Manually move the axis.
- Correct the machining program.
T02 Reset signal ON 0203
Details
The reset has been entered.
Remedy
- The program execution position has returned to the start of the program. Execute automatic
operation from the start of the machining program.
Summary of Contents for E70 Series
