background image

ACTIVE DRIVER M/M 1.1 

ACTIVE DRIVER M/T 1.0  -  ACTIVE DRIVER M/T 2.2 

ACTIVE DRIVER T/T 3.0  -  ACTIVE DRIVER T/T 5.5

DICHIARAZIONE DI CONFORMITÀ 

La Ditta DAB PUMPS s.p.a. - Via M. Polo,14 - Mestrino (PD) - ITALIA - sotto la propria 
esclusiva responsabilità dichiara che i prodotti summenzionati sono conformi a: 

Direttiva della Compatibilità elettromagnetica 2004/108/CE e successive modifiche. 

Direttiva Bassa Tensione 2006/95/CE e successive modifiche. 

DÉCLARATION DE CONFORMITÉ 

La société DAB PUMPS s.p.a. – Via M. Polo, 14 – Mestrino (PD) – ITALY – sous sa propre 
responsabilité exclusive déclare que les produits susmentionnés sont conformes à: 

Directive de la Compatibilité électromagnétique 2004/108/CE et modifications successives. 

Directive Basse Tension 2006/95/CE et modifications successives. 

DECLARATION OF CONFORMITY 

The Company DAB PUMPS s.p.a. – Via M. Polo, 14 – Mestrino (PD) – ITALY – under is own 
exclusive responsibility declares that the products listed above comply with: 

Directive on Electromagnetic Compatibility 2004/108/CE and subsequent modifications. 

Directive on Low Voltage 2006/95/CE and subsequent modifications. 

KONFORMITÄTSERKLÄRUNG 

Die Firma DAB PUMPS s.p.a. – Via M. Polo, 14 – Mestrino (PD) – ITALIEN – erklärt 
eigenverantwortlich, dass die vorstehend beschriebenen Produkte den folgenden Richtlinien 
entsprechen:

Richtlinie zur elektromagnetischen Verträglichkeit 2004/108/CE und folgende Änderungen. 

Niederspannungsrichtlinie 2006/95/CE und folgende Änderungen. 

CONFORMITEITSVERKLARING

De firma DAB PUMPS s.p.a. – Via M.  Polo, 14 – Mestrino (PD) – ITALY – verklaart onder 
haar eigen, exclusieve verantwoording dat de hieronder genoemde producten voldoen aan: 

Richtlijn elektromagnetische compatibiliteit 2004/108/CE en successievelijke wijzigingen. 

Laagspanningsrichtlijn 2006/95/CE en successievelijke wijzigingen. 

DECLARACIÓN DE CONFORMIDAD 

La empresa DAB PUMPS s.p.a. – Via M. Polo, 14 – Mestrino (PD) – ITALIA – declara bajo su 
total responsabilidad que los productos anteriormente mencionados cumplen la: 

Directiva de Compatibilidad Electromagnética 2004/108/CE y sucesivas modificaciones. 

Directiva de Baja Tensión 2006/95/CE y sucesivas modificaciones. 

FÖRSÄKRAN OM CE-ÖVERENSSTÄMMELSE 

Företaget DAB PUMPS s.p.a. – Via M.  Polo 14, Mestrino (PD) – ITALIEN – förklarar på eget 
ansvar att ovannämnda produkter är i överensstämmelse med: 

EMC-direktivet 2004/108/EEG jämte ändringar. 

Lågspänningsdirektivet 2006/95/EEG jämte ändringar. 

Summary of Contents for ACTIVE DRIVER M/M 1.1







































Reviews: