LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 411

Page: 411 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

136

PGM 191

ACD/UCD

Flex

Btn

Description

Default

Values

the station in UCD DND and unavailable for group calls. A setting of ‘00’ disables

automatic ACD DND.

increments

Queued call Tone

When enabled (On), the first group member assigned in Program 190 for the group

receives a single 0.4 second burst of muted ring when a call is queued to the group.

0 (Off)

0 = Off

1 = On

Group Name

Assign

This parameter assigns a name, maximum 12 characters, to the group.

Not assigned

12 Characters

Call Coverage

The Call Coverage parameter enables coverage for the Hunt Group. A Call

Coverage Flexible button at a covering station for the group will be active. The

covering station must have a Coverage button set using Station User Program

codes, 46 and group number.

Flexible button 1 = Hunt Coverage Mode On/Off

Flexible button 2 = Delay Ring Cycle

Button 1 =0 (Off)

Button 2 = 0

0 = Off

1 = On

0 ~ 9 cycles

3.7.2.3 Ring Group Attributes

PGM 191

Ring

Flex

Btn

Description

Default

Values

VMIB Announce

1 Timer

This parameter defines the time the system waits to automatically answer an

incoming call and play the assigned VMIB announcement (Flexible button 3)

015 seconds

000 ~ 999 in 1

second increments

VMIB Announce

2 Timer

This parameter defines the time the system waits after playing the first

announcement to play the assigned VMIB announcement 2 (Flexible button 4) to a

queued call.

000 seconds

000 ~ 999 in 1

second increments

VMIB Announce

1 Location

This parameter assigns the VMIB announcement number to play when the VMIB

Announce 1 timer (Flexible button 1) expires.

Not assigned

00 ~ 70

VMIB Announce

This parameter assigns the VMIB announcement number to play when the VMIB

Not assigned

00 ~ 70

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands