manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Share
Download
LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 242

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

234 

  If the originator does not answer the call back ring within the Call Back ring time (30 

seconds), the call is dropped. 

 

Reference 

A.  Station Message Wait/Call Back 

 

Admin Programming 

Networking Basic Attribute (PGM 320) 
 
 

16.6.3 

Network Call Forward 

Description 

A user can forward (send) their calls to another station, Station Group or a user’s VMIB mailbox 
across the private network.    The user may forward all calls immediately, if the user does not 
answer the call or if the station is busy.    In addition, the user may select to activate ‘Follow-me’ 
forward, forwarding calls from a location other than the station.  Calls forward in the same 
manner as a Call Forward within a system (refer to Ref. A) and is transparent to the user. 
 
From a network perspective, the ipLDK can use either the ‘Join’ or ‘Re-route’ signaling method 
to complete a call forward over the network.  The Networking Transfer Mode assigns the 
method that will be used and should be selected to match other systems connected in the 
private network. 

  Join - an additional connecting path is needed to transfer the call to another station. 

  Routing - a new connecting path is used to forward the call. 

 

Consideration 

  To use Call Forward, a station must be permitted to forward calls in the system database. 

  Authorization codes are required for ‘Follow-me’ Call Forward and may be required to 

activate Network Call Forward ‘Follow-Me’ 

  A station is separately allowed Call Forward and Off-Net Call Forward. 

  The ipLDK does not check the status of the receiving destination; once forward is 

activated, the receiving system is responsible for routing the call. 

  Incoming analog CO lines must provide Disconnect Supervision and the Open Loop 

Detect timer must be set for proper operation. 

  Station calls may automatically forward using Preset Call Forward or may forward to the 

user’s VMIB voice mailbox after the VMIB Forward time.    If the Preset Call Forward or 
VMIB Forward timers are shorter then the Call Forward No-Answer timer, calls will not 
forward over the network. 

  Network Call Forward ‘Follow-Me’ can only be deactivated at the original station. 

 Network Call Forward Follow-Me is only available when employing H.323/H.450 

networking.  When employing QSig Call Forward ‘Follow-me’ is not available over the 
network. 

  For proper operation of Call Forward Follow-Me, all ipLDK systems in the network must 

employ the same type of Authorization codes, 5-digit or variable length. 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands