manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Share
Download
LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 202

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

194 

 

13.8  CO Call Forward Off-Net 

Description 

An Attendant can direct the system to re-route (forward) incoming CO line calls to a directory 
(telephone) number outside the system assigned to a Speed Dial.    When a call is received on 
the CO line, the system immediately accesses an outgoing CO line and dials the telephone 
number from the Speed Dial number.  The system then establishes an Unsupervised 
Conference between the CO lines.  The system will automatically disconnect the call if an 
open loop is detected based on the Open Loop Detect timer or after the Unsupervised 
Conference Timer has expired. 
 

Operation 

To activate incoming CO Call Forward Off-Net at the Attendant, 

1.  Lift the handset or press the On/Off button. 
2.  Press the [DND/FOR] button. 
3.  Dial Off-Net Call Forward code, 7. 
4.  Access the desired CO line or Group. 
5.  Dial the Speed Dial bin number with the desired telephone number. 
6.  Replace the Handset and go on-hook. 

 
To deactivate CO Call Forward Off-Net from the attendant, 

1.  Lift the Handset or press the [MON] button. 
2.  Press the [DND/FOR] button. 
3.  Dial Call Forward code 7. 
4.  Access the desired CO line or Group. 
5. Dial 

#. 

 

Consideration 

 

Considerations

 associated with Call Forward and Unsupervised Conference apply. 

  If an idle CO Line is not available to place the outgoing CO line call, Off-net Call Forward 

is not activated. 

  DID lines are not subject to CO Call Forward Off-Net. 

  When activating CO Call Forward Off-Net, a Speed Dial Flexible button may be used in 

place of dialing the Speed bin. 

  Toll restriction will be based on the COS of outgoing CO Line. 

 

Reference 

A. Call Forward 
B. Unsupervised Conference 
C.  Basic Outbound Access 

 

Administration 

System Numbering Plan (PGM 109, Flexible button 6) 
 

Assigns the Unsupervised Conference Timer Extend Code   

Intercom Tenancy Group Attendant (PGM 120, Flexible 1) 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands