manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Share
Download
LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 232

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

224 

 

15.4  SIP (Session Initiation Protocol) 

Description 

SIP (Session Initiation Protocol) is an IETF (Internet Engineering Task Force) recognized 
protocol (RFC-3261) to establish, maintain and terminate multimedia sessions between 
endpoints over an IP network.    SIP, is an application layer control protocol that employs other 
protocols, such as SDP (Session Description Protocol) to describe the desired connection 
characteristics and other lower layer protocols. 
 
ipLDK-60 operates in two distinct SIP modes based on the SIP call server routing of incoming 
calls.    The first mode is based on the SIP Register ‘method’; in this case, the system registers 
a SIP User ID to the SIP call server ‘Registrar’, which identifies the location to receive calls.   
The second mode is ‘SIP Trunking’; the SIP call server routes calls to a designated IP endpoint, 
in this case, the ipLDK VOIB IP address or a proxy.  In either case, the VOIB CO line can 
provide ‘Normal’ or ‘DID/MSN’ service.    Once active at the ipLDK-60, incoming and outgoing 
calls are routed and handled as with the type of service and other attributes assigned for the 
station and VOIB CO line. 
 

15.4.1 

Configuring SIP Trunks 

Description 

The following is a quick guide to SIP Trunk configuration, 

 

Set the Ext or CO ATD Code CLI (PGM 114) 
CLIP/COLP Table for CO line has priority 

 

Set CO Service Type for ‘Normal’ or ‘DID’ service (PGM 140) 

 

Set the CO line group for the VOIB CO lines (PGM 141) 

 

Set ISDN line characteristics (PGM 143) 
including CLIP and COLP, as desired 

 

Set ISDN Call Type as (PGM 143) 

 

Set ISDN Enblock Send as ‘On’, all IP calls are Enblock (PGM 143) 

 

Set DID CONV Type, Digit Mask, etc., if required, (PGM 143) 

 

Set Ring Assignments, if required (PGM 145) 

 

Set the Enblock Timer, if required (PGM 181) 

 

DID Tables, if required, (PGM 167 and 231) 

 

Set Networking CO Line Type as SIP (PGM 322) 

 

Configure VOIB IP settings, as required (PGM 340) 
IP addresses, VOIB, Gateway DNS 
Set VOIB Mode to SIP 
Enter Firewall WAN address, if required 

 

Set Proxy Server Address as URL or IP address of Proxy or Call Server (PGM 500 PC 
Admin only) 

 

Set Domain as URL or IP address for SIP Call Server (PGM 500 PC Admin only) 

 
Reset after programming to assure channel sync 
 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands