LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 394

Page: 394 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

119

3.5.21.2 System Timers II (PGM 181)

PGM 181 is one of three PGMs used to define timers that affect system wide operations. See also PGM 180 and 182.

Procedure:

1. Press

the

[TRANS PGM]

button.

2. Dial

181.

3. Select the desired Flexible button.

4. Enter the appropriate value.

5. Press

the

[Hold/Save]

button.

PGM

181

Flex

Btn

Description

Default

Values

Call Forward No

Answer Timer

This parameter sets the No-answer Forward time, if No-answer Call Forward is

active at the station, when the timer expires the call is rerouted to the designated

destination.

015 seconds

000 ~ 255 in 1

second increments

DID/DISA No

Answer Timer

This parameter sets the time a DID/DISA call will ring the station before it is rerouted

to the DID/DISA No-answer destination (PGM 167, Flexible button 3).

25 seconds

00 ~ 99 in 1 second

increments

VMIB User

Record Timer

This parameter determines the maximum duration of the user recorded greeting for

the VMIB Voice Mail. Longer greetings cannot be stored.

020 seconds

010 ~ 255 in 1

second increments

VMIB Valid User

Message Timer

This parameter establishes the minimum duration the ipLDK will recognize as a

legitimate Voice Mail, shorter messages are discarded. If set to ‘0’, a message

cannot be recorded in the VMIB.

4 seconds

0 ~ 9 in 1 second

increments

Door Open Time

This parameter sets the duration the Door Open contact will remain activated when a

station dials the Door Open code.

20 (2 seconds)

05 ~ 99 in 100 milli-

second increments

ICM Box Timer

This parameter sets the duration a station receives Door Phone ring when the Door

Phone ‘Call’ button is pressed.

30 seconds

00 ~ 60 in 1 second

increments

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands