manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Share
Download
LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 131

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

123 

 

8  P

AGING 

S

ERVICES

 

8.1 

Internal, External Zone and All Call Paging 

Description 

A station, which is permitted to access Page facilities, can connect and transmit voice 
announcements to any or all of the systems Internal and External Page zones.    A DKT Station 
can be assigned to receive announcements from any combination of zones or not to receive 
Page announcements. 
 
A Page Warning tone, if assigned, will be provided to the Page Zone(s) prior to the audio 
connection.    The user is allowed to continue the page for the Page Time-out timer after which 
the user is disconnected and the Page Zone(s) is returned to idle. 
 
Page Zones and the access codes for paging are shown in the following table. 

Page ZONE 

Code 

ITEM 

501-505 Internal 

Page 

Zones 

543 

Internal All Call Page 

545 External 

Page 

Zone 

 

549 

All Call Page (Internal & External) 

 
Flexible buttons of a DKT may be assigned to access a Page Zone. 
 

Operation 

To initiate a Page announcement, 

1.  Lift the handset. 
2.  Dial the desired Page Zone code. 
3.  After the Page Warning tone, if assigned, make the desired announcement. 
4.  Replace the handset to return to idle. 

 

Consideration 

  When External Page is required, appropriate external equipment should be attached to 

the External Page port. 

  An External Control Contact may be assigned to activate when External Page is 

accessed to turn on an amplifier or connect voice to the amplifier. 

  A station, which is in DND or busy, will not receive paging announcements. 

  A station, which is not allowed to Page Access, cannot initiate a Page but may still 

receive announcements. 

  The ipLDK-60 allows only a single internal Page at a time.  Attempting to initiate an 

internal page including All Call Page while another internal or All Call Page is in progress 
will return error tone.    An internal Page is possible at the same time as another External 
page except for All Call Paging. 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands