LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 301

Page: 301 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

PGM

111

Flex

Btn

Description

Default

Values

1: Flash Drop, the active call is dropped

2: Flash ignore, the flash is ignored, no action is taken

3: Hold Release, the active call is placed on hold and the user receives dial

tone, the held call is disconnected if the user hangs up

Loop LCR

Account Code

If this value is set to On, the station user must enter an Account Code to use Loop

LCR.

0 (Off)

0 = Off

1 = On

VMIB Message

Type

This parameter determines the order of Voice Mail message playback.

0 = LIFO, Last-in, First-out

1 = FIFO, First-in, First-out

1 (FIFO)

0 = LIFO

1 = FIFO

Off-Net Call

Forward

When enabled (On), the station is permitted to activate Off-Net Call Forward. The

user can forward calls over a CO line. See PGM 112, Flexible button 12 to define

the type of calls that will forward.

1 (Disable)

0 = Enable

1 = Disable

Forced Hands

Free

When enabled (On), the station can change the Intercom Signal mode of the called

station from Tone to Handsfree.

1 (On)

0 = Off

1 = On

Reserved 20

Reserved 21

Caller Voice Over

When this parameter is On, the station can place calls to other stations using Voice

Over. The receiving station must be enabled to receive Voice Over, PGM 113

Flexible button 6.

0 (Off)

0 = Off

1 = On

SIP User ID

Table Index

This parameter determines the caller id for a station when employing SIP for a call.

When using SIP, the caller id is based on the CLIP/COLP (PGM 143 Flexible button

1 and 2) or the User ID defined from the SIP User ID Table index (PGM 501) entered

here.

00 00-16

Redial DTMF

When enabled (On), the station receives DTMF tones during Redial.

1 (On)

0 = Off

1 = On

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands