manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Share
Download
LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 47

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

39 

 

3.10  Hot Line & Warm Line 

Description 

When a user goes ‘off-hook’, the system normally provides ICM dial tone.    If desired, a station 
can be assigned to access a pre-assigned Idle Line Selection system resource (Hot Line).  
The Hot Line can be any of the Idle Line settings: 

  Seize a CO Line, 

  Call another station, 

  Activate a Flexible button feature. 

 
As a Hot Line, the Idle Line is accessed immediately.  As a Warm Line, the user receives 
internal dial tone and after the Warm Line time, the Idle Line is accessed. 
 

Operation 

To activate a Hot Line/Warm Line, 

1.  Lift the handset or press the On/Off button. 
2.  The Hot Line is activated immediately.    The Warm Line is accessed if there is no 

activity for the Warm Line time. 

 

Consideration 

  For proper operation, the Warm Line Timer should be less than the Dial Tone time-out 

Timer. 

  An SLT may be assigned a Hot/Warm Line. 

  Preferred Line Answer takes precedence over Hot/Warm Line. 

 

Reference 

A.  Preferred Line Answer (PLA) 

 

Admin Programming 

Warm Line (PGM 113, Flexible button 7) 
 

Assigns Idle Line Selection as Hot or Warm 

Idle Line Selection (PGM 122) 
 

Assigns Idle Line Selection to a station range 

Warm Line Timer (PGM 182, Flexible button 8) 
 

Sets the Warm Line time 

 
 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands