manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

The LG-Ericsson ipldk-60 is an advanced telephony system offering an array of features for seamless communication. For a comprehensive understanding of its hardware setup and installation process, download the user manual for free at manualshive.com. The manual provides detailed instructions and serves as a helpful resource for users.

Share
Download
background image

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

216 

 

14.8  Multiple Subscriber Number (MSN) 

Description 

MSN enables assigning multiple subscriber numbers to one ISDN Interface, allowing Direct-
Dial-In like call delivery.    In addition, Sub-Address information may be included as additional 
digits in the Called Party Number Information Element allowing for similar call routing by the 
ipLDK.    When MSN or Sub-address information is received, the system references the MSN 
Table for an index to the Flexible DID Table, which then determines call routing. 
 
A station may be assigned an MSN button.  If a call is received for the assigned MSN, the 
station receives ring and the MSN button will act as the call appearance.  In addition, if 
assigned, the user will receive call waiting for the MSN call   
 

Consideration

 

  If the Called Party Number from the ISDN does not match an MSN Table entry, the 

received digits are treated as defined for DID calls to determine routing of the call. 

  The MSN Table employs the CO Line entry as a quick look-up reference.    If the CO line 

number is programmed in the MSN Table, then only those entries with the CO line 
number are searched, otherwise the entire MSN Table is searched for a match to the 
Called Party Number. 

  The ipLDK allows the sub-address to be delivered in the Called Party Number (CPN) or in 

the CPN Sub-address field of the Call Set-up message.  The sub-address delivery is 

defined in the S

o

 Sub-address for each station. 

  The sub-address cannot exceed a single digit, 0 – 9. 

  Up to 250 entries can be made in the MSN Table. 

  To use an ISDN CO line with MSN, the CO Service type should be set to DID/MSN. 

 

Reference 

A. DID 
B. ICLID Routing 

 

Admin Programming 

CO Line Service Type (PGM 140, Flexible button 1) 
 

Assigns the type o f service for the line, must be ISDN DID/MSN 

MSN Wait (PGM 114, Flexible button 20) 
 

Enables call wait for MSN calls to the station when busy 

ISDN Calling Sub-address (PGM 146, Flexible button 4) 
 

Enables sending the sub-address of the ISDN station when placing a call 

MSN Table (PGM 202) 
 

Assigns an index to the Flexible DID Table (PGM 231) for call routing 

 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ipldk-60

Panasonic KX-PRX150AZ Quick Manual preview
KX-PRX150AZ
Brand: Panasonic Pages: 32
Karel MS48 Mini-Manual preview
MS48
Brand: Karel Pages: 43
Uniden EXI8560 - EXI 8560 Cordless Phone Owner'S Manual preview
EXI8560 - EXI 8560 Cordless Phone
Brand: Uniden Pages: 12
Uniden EXI4560 - EXI 4560 Cordless Phone Manual Del Usuario preview
EXI4560 - EXI 4560 Cordless Phone
Brand: Uniden Pages: 48
Uniden EXI4246 - EXI 4246 Cordless Phone Manual D'Utilisation preview
EXI4246 - EXI 4246 Cordless Phone
Brand: Uniden Pages: 48
Uniden EXAI5680 - EXAI 5680 Cordless Phone Manual Del Usuario preview
EXAI5680 - EXAI 5680 Cordless Phone
Brand: Uniden Pages: 64
Uniden EXAI3248 Series Manual D'Utilisation preview
EXAI3248 Series
Brand: Uniden Pages: 68
Uniden DXI7286-2 Guía De Referencia Rápida preview
DXI7286-2
Brand: Uniden Pages: 48
Uniden DXI7286-2 Manual D'Utilisation preview
DXI7286-2
Brand: Uniden Pages: 52
Uniden DXI 4286-2 Series Owner'S Manual preview
DXI 4286-2 Series
Brand: Uniden Pages: 48
Uniden DXI 4286-2 Series Guide Utilisateur preview
DXI 4286-2 Series
Brand: Uniden Pages: 52
Uniden EXS 2010 Mode D'Emploi preview
EXS 2010
Brand: Uniden Pages: 29
Uniden EXP7241 Series Manual D'Utilisation preview
EXP7241 Series
Brand: Uniden Pages: 12
Uniden EXP7241 Series Guía De Referencia Rápida preview
EXP7241 Series
Brand: Uniden Pages: 16
Uniden EXP 7900 Series Manual preview
EXP 7900 Series
Brand: Uniden Pages: 12
Uniden EXP 7900 Series Owner'S Manual preview
EXP 7900 Series
Brand: Uniden Pages: 12
Uniden DXAI5588-3 Series Guide Utilisateur preview
DXAI5588-3 Series
Brand: Uniden Pages: 72
Uniden DECT2080 Series User Manual preview
DECT2080 Series
Brand: Uniden Pages: 64

Brands by name

Popular brands

Load more brands