LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 340

Page: 340 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

PGM

142

Flex

Btn

Description

Default

Values

Reverse (NPR)

Line Drop CPT

(Call Progress

Tone)

If this parameter is On, the system monitors incoming CO line calls, if after answer

dial tone is detected, the CO line is dropped. Thus, a station cannot receive dial

tone as a transfer and defeat Toll Restriction.

0 (Off)

0 = Off

1 = On

CO Distinct Ring

CO lines can be assigned one of 5 ring tones for incoming calls. When different ring

tones are assigned to each CO line, the ringing CO line can be determined from the

tone.

0 – 4

CO Line MOH

CO lines may be assigned separate sources for MOH overriding the system wide

assignments in PGM 171. When the CO Line MOH here is ‘Not assigned’ (0), the

assignments in PGM 171 apply to the CO line.

1 (Internal Music)

0 = Not assigned

1 = Internal Music

2 = External Music

3 = Reserved

4 – 8 = SLT MOH 1-5

9 = Hold Tone

Supply PABX-CO

Dial Tone

No (PABX/CO)

Yes = ipLDK-60

No = PABX/CO

Supply PABX-CO

Ring Back Tone

No (PABX/CO)

Yes = ipLDK-60

No = PABX/CO

Supply PABX-CO

Error Tone

No (PABX/CO)

Yes = ipLDK-60

No = PABX/CO

Supply PABX-CO

Busy Tone

No (PABX/CO)

Yes = ipLDK-60

No = PABX/CO

Supply PABX-CO

Announce Tone

In some cases, the PABX or PSTN may not provide certain tones to the CO line. In

this case, the ipLDK-60 can provide these tones to the station in place of the CO

line. When this parameter is assigned ‘Yes’ the ipLDK-60 provides the tone

otherwise, the PABX or PSTN is expected to provide the tone. Select the desired

Flexible button for the specific Tone.

No (PABX/CO)

Yes = ipLDK-60

No = PABX/CO

CO Flash Timer

This parameter defines the length of a Flash on the PABX/CO line. The Flash type

is defined in PGM 141, Flexible button 7.

050 (500 msec.)

000 – 300 in 10-milli-

second increments

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands