manualshive.com logo in svg

LG-Ericsson ipldk-60, Feature Description And Operation Manual

The LG-Ericsson ipldk-60 is an advanced telephony system offering an array of features for seamless communication. For a comprehensive understanding of its hardware setup and installation process, download the user manual for free at manualshive.com. The manual provides detailed instructions and serves as a helpful resource for users.

Share
Download
background image

 
 

Issue 2.2 

Feature Description and Operation Manual 

 

 

 

 

 

 

218 

 

15 V

O

IP

 

S

ERVICE

 

Description 

The ipLDK-60 can be equipped with up to 8 IP channels to support remote LG-Ericsson IP 
Phones, Phontage (LG-Ericsson IP softphone) and IP CO lines for networking (refer to Ref A) 
or trunking.    Up to 16 IP Phones, which include Phontage softphones, can be registered with 
an ipLDK-60.    Each active call from/to an IP Phone or IP CO line requires a VOIB IP channel.   
When all channels are busy, such calls will receive fast-busy tone as an indication of all 
channels busy. 
 
IP CO lines support both H.323 and SIP (Session Initiation Protocol) to establish, maintain and 
terminate IP calls.    The ipLDK supports both SIP Trunking to provide SIP access as a normal 
CO line or SIP Register for incoming call routing to specific authenticated users. 
 
 

15.1  H.323 

Description 

H.323 is an IEEE standard for multimedia communications “over an unreliable network”.  In 
particular, H.323 is intended for use over IP networks where delivery of individual packets is not 
guaranteed.    In H.323, terminals can register with a GateKeeper for communication services; 
the GateKeeper then manages the services to the terminal.  H.323 employs several other 
IEEE standards including H.245 for control signaling and H.225 for Call and RAS channel 
signaling. 
 
ipLDK operates in two modes employing H.323 with a GateKeeper for H.323 trunking and 
without the GateKeeper for Private Networking (refer to Ref. A).    How to configure both modes 
of H.323 operation are provided; refer to section 15.1.1 for guidelines to configure operation 
with a GateKeeper.    Private Network configuration using H.323 is provided in section 16.7.2.   
In addition, ipLDK supports several options to improve efficiency and reduce connection set-up 
times.  Options supported include: 

 

Fast Mode 
ipLDK can establish a media channel using H.245 or the H.323 Fast Mode. 

 

Early H.245 
ipLDK implements the early H.245 option; the H245 channel address is provided in the 
call Setup message hence speeding call setup. 

 

H.245 Tunnel 
ipLDK implements the H.245 tunneling for control and security by encapsulating H.245 in 
Q.931 messages 

 

Consideration 

  The TOS byte of the IP packet can be defined in the ipLDK to adjust precedence of voice 

communication packets. 

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ipldk-60

Panasonic KX-TG1611 Operating Instructions Manual preview
KX-TG1611
Brand: Panasonic Pages: 32
Panasonic KX-PRD262 Quick Manual preview
KX-PRD262
Brand: Panasonic Pages: 10
Aastra ITE Agent User Manual preview
ITE Agent
Brand: Aastra Pages: 91
Aastra 6730a Operation Manual preview
6730a
Brand: Aastra Pages: 20
Uniden EXP95I Important Safety Instructions Manual preview
EXP95I
Brand: Uniden Pages: 47
Telos DESKTOP DIRECTOR 2101 User Manual preview
DESKTOP DIRECTOR 2101
Brand: Telos Pages: 46
Esse-ti ST 201 User Manual preview
ST 201
Brand: Esse-ti Pages: 32
Vingtor Stentofon VSP-211M-L User Manual preview
VSP-211M-L
Brand: Vingtor Stentofon Pages: 4
Savannah Speros NEC User Manual preview
Speros NEC
Brand: Savannah Pages: 9
JOIWO JWAT410 Series User Manual preview
JWAT410 Series
Brand: JOIWO Pages: 6
GE EX29350 User Manual preview
EX29350
Brand: GE Pages: 9
AEG STYLE 12 User Manual preview
STYLE 12
Brand: AEG Pages: 84
AEG Voxtel C50 Quick Start Manual preview
Voxtel C50
Brand: AEG Pages: 8
AEG STYLE 10 User Manual preview
STYLE 10
Brand: AEG Pages: 48
AEG voxtel c110 Quick Start Manual preview
voxtel c110
Brand: AEG Pages: 120
AEG Voxtel C115 Quick Start Manual preview
Voxtel C115
Brand: AEG Pages: 156
Grundig D1110 Manual preview
D1110
Brand: Grundig Pages: 25
Panasonic KX-DT 333 Series Brochure & Specs preview
KX-DT 333 Series
Brand: Panasonic Pages: 4

Brands by name

Popular brands

Load more brands