LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 352

Page: 352 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

3.3.9

T1 CO Line Attributes (PGM 152)

PGM 152 defines various attributes associated with T1 CO lines.

Procedure:

1. Press

the

[TRANS/PGM]

button.

2. Dial

152.

3. Enter the appropriate CO Line Range.

4. Press the desired Flexible button.

5. Enter the appropriate value.

6. Press

the

[Hold/Save]

button.

PGM

152

Flex

Btn

Description

Default

Values

Pause Duration

This parameter sets the duration of the delay in dialing when a pause is encountered

in a Speed Dial number.

2 seconds

1 ~ 9 in 1-second

increments

Release Guard

Time

This parameter defines the interval between when a user disconnects from a T1 CO

line call and when the CO line is available for access by another user. This interval

allows time for the CO to return the circuit to an idle state.

20 (2 seconds)

01 ~ 60 in 100-milli-

second increments

Dial tone Delay

Timer

This parameter sets the time between the user accessing a T1 CO line and dial tone

delivery to the user. This interval allows the T1 CO line to setup the circuit. If Dial

Tone Detect (PGM 160, Flexible button 6) is enabled, when dial tone is detected, it is

immediately sent to the user otherwise, this timer is employed.

10 (1 second)

02 ~ 50 in 100-milli-

second increments

Inter-digit Timer

not used

Wink Timer

This parameter sets the duration of the ‘Wink’ signal for Wink start T1 CO lines. The

parameter is also used to define the delay when delay start is assigned for the T1

CO line.

10 (200 milli-

seconds)

07 ~ 15 in 20-milli-

second increments

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Related manuals for ipldk-60

Brands by name

Popular brands