Hitachi WJ200-001L, Instruction Manual

Page: 654 / 680

Ver.3
−
− −
−
145
O O O Output Function Summary Table utput Function Summary Table utput Function Summary Table utput Function Summary Table – This table shows all functions for the logical outputs (terminals [11],
[12] and [AL]) at a glance. Detailed descriptions of these functions, related parameters and settings, and
example wiring diagrams are in “Using Intelligent Output Terminals” on page 39.
O O O Output Function Summary Table utput Function Summary Table utput Function Summary Table utput Function Summary Table
O
O O
Option
ption ption
ption
C C C Code ode ode ode
T
T T
Terminal
erminal erminal
erminal
S S S Symbol ymbol ymbol ymbol
F F F Function Name unction Name unction Name unction Name D D D Description escription escription escription
00
00 00
00 RUN Run Signal ON When the inverter is in Run Mode
OFF When the inverter is in Stop Mode
0
0 0
01
1 1
1 FA1 Frequency Arrival
Type 1–Constant Speed ON When output to motor is at the set frequency
OFF When output to motor is OFF, or in any
acceleration or deceleration ramp
0
0 0
02
2 2
2 FA2 Frequency Arrival
Type 2–Over frequency ON When output to motor is at or above the set freq,
even if in accel (C
C C C0 0 0 042 42 42 42) or decel (C C C C0 0 0 043 43 43 43) ramps
OFF When output to motor is OFF,
or at a level below the set frequency
0 0 0 03 3 3 3 OL Overload Advance
Notice Signal 1 ON When output current is more than the set
threshold (C
C C C0 0 0 04 4 4 41 1 1 1) for the overload signal
OFF When output current is less than the set
threshold for the deviation signal
0
0 0
04
4 4
4 OD Output Deviation
for PID Control ON When PID error is more than the set threshold
for the deviation signal
OFF When PID error is less than the set threshold for
the deviation signal
0 0 0 05 5 5 5 AL Alarm Signal ON When an alarm signal has occurred and has not
been cleared
OFF When no alarm has occurred since the last
cleaning of alarm(s)
0
0 0
06
6 6
6 FA3 Frequency Arrival
Type 3–Set frequency ON When output to motor is at the set frequency,
during accel (C
C C
C0
0 0
042
42 42
42) and decel (C
C C
C0
0 0
043
43 43
43).
OFF When output to motor is OFF,
or is not at a level of the set frequency
0 0 0 07 7 7 7 OTQ Over/under Torque
Signal ON Estimated motor torque exceeds
the specified level
OFF Estimated motor torque is lower than
the specified level
0
0 0
09
9 9
9 UV Undervoltage ON Inverter is in Undervoltage
OFF Inverter is not in Undervoltage
1
1 1
10
0 0
0 TRQ Torque Limited Signal ON Torque limit function is executing
OFF Torque limit function is not executing
11 11 11 11 RNT Run Time Expired ON Total running time of the inverter exceeds
the specified value
OFF Total running time of the inverter does not
exceed the specified value
1 1 1 12 2 2 2
ONT Power ON time
Expired ON Total power ON time of the inverter exceeds
the specified value
OFF Total power ON time of the inverter does not
exceed the specified value
1 1 1 13 3 3 3 THM Thermal Warning ON Accumulated thermal count exceeds
the C
C C C0 0 0 06 6 6 61 1 1 1 set value
OFF Accumulated thermal count does not exceed the
C
C C
C0
0 0
06
6 6
61
1 1
1 set value
1 1 1 19 9 9 9
BRK Brake Release Signal ON Output for brake release
OFF No action for brake
2
2 2
20
0 0
0 BER Brake Error Signal ON Brake error has occurred
OFF Brake performance is normal
2 2 2 21 1 1 1 ZS Zero Hz Speed
Detection Signal ON Output frequency falls below the threshold
specified in C
C C
C0
0 0
06
6 6
63
3 3
3
OFF Output frequency is higher than the threshold
specified in C C C C0 0 0 06 6 6 63 3 3 3
22 22 22 22 DSE Speed Deviation
Excessive ON Deviation of speed command and actual speed
exceeds the specified value P
P P P0 0 0 02 2 2 27 7 7 7.
OFF Deviation of speed command and actual speed
does not exceed the specified value P
P P
P0
0 0
02
2 2
27
7 7
7.
23
23 23
23 POK Positioning Completion ON Positioning is completed
OFF Positioning is not completed