Hitachi WJ200-001L, Instruction Manual

Page: 498 / 680

Ver.2

69
Input Function Summary Table
Option
Code
Terminal
Symbol
Function Name Description
OFF
Selects the direction of motor rotation: OFF = REV. While
the motor is rotating, a change of F/R will start a
deceleration, followed by a change in direction
 PID PID Disable
ON
Temporarily disables PID loop control. Inverter output turns
OFF as long as PID Enable is active (

=

)
OFF
Has no effect on PID loop operation, which operates
normally if PID Enable is active (

=

)
 PIDC PID Reset
ON
Resets the PID loop controller. The main consequence is that
the integrator sum is forced to zero
OFF No effect on PID controller
 UP
Remote Control UP
Function (motorized
speed pot.)
ON
Accelerates (increases output frequency) motor from current
frequency
OFF Output to motor operates normally
 DWN
Remote Control Down
Function (motorized
speed pot.)
ON
Decelerates (decreases output frequency) motor from current
frequency
OFF Output to motor operates normally
 UDC
Remote Control Data
Clearing ON
Clears the UP/DWN frequency memory by forcing it to equal
the set frequency parameter F001. Setting

must be
set=

to enable this function to work
OFF UP/DWN frequency memory is not changed

OPE Operator Control
ON
Forces the source of the output frequency setting

and
the source of the Run command

to be from the digital
operator
OFF
Source of output frequency set by

and source of Run
command set by

is used
 SF1
Multi-speed Select,
Bit operation Bit 1 ON Bit encoded speed select, Bit 1, logical 1
OFF Bit encoded speed select, Bit 1, logical 0
 SF2
Multi-speed Select,
Bit operation Bit 2 ON Bit encoded speed select, Bit 2, logical 1
OFF Bit encoded speed select, Bit 2, logical 0
 SF3
Multi-speed Select,
Bit operation Bit 3 ON Bit encoded speed select, Bit 3, logical 1
OFF Bit encoded speed select, Bit 3, logical 0
 SF4
Multi-speed Select,
Bit operation Bit 4 ON Bit encoded speed select, Bit 4, logical 1
OFF Bit encoded speed select, Bit 4, logical 0
 SF5
Multi-speed Select,
Bit operation Bit 5 ON Bit encoded speed select, Bit 5, logical 1
OFF Bit encoded speed select, Bit 5, logical 0
 SF6
Multi-speed Select,
Bit operation Bit 6 ON Bit encoded speed select, Bit 6, logical 1
OFF Bit encoded speed select, Bit 6, logical 0
 SF7
Multi-speed Select,
Bit operation Bit 7 ON Bit encoded speed select, Bit 7, logical 1
OFF Bit encoded speed select, Bit 7, logical 0
 OLR
Overload Restriction
Source Changeover ON Perform overload restriction
OFF Normal operation
 TL Torque Limit Selection
ON Setting of

is enabled
OFF Max. torque is limited with 200%
 TRQ1 Torque limit switch 1
ON
Torque limit related parameters of Powering/regen, and
FW/RV modes are selected by the combinations of these
inputs.
OFF
 TRQ2 Torque limit switch 2
ON
OFF
Input Function Summary Table
Option
Code
Terminal
Symbol
Function Name Description
 BOK Brake confirmation
ON
Brake wait time (

) is valid
OFF
Brake wait time (

) is not valid
 LAC LAD cancellation
ON
Set ramp times are ignored. Inverter output immediately
follows the freq. command.
OFF Accel. and/or decel. is according to the set ramp time
 PCLR Pulse counter clear
ON Clear the position deviation data
OFF Maintain the position deviation data
 ADD ADD frequency enable
ON
Adds the

(add frequency) value to the output frequency
OFF Does not add the

value to the output frequency