Hitachi WJ200-001L, Instruction Manual

Page: 650 / 680

Ver.3
−
− −
−
141
IIIInput Function S nput Function S nput Function S nput Function Su u u ummary Table mmary Table mmary Table mmary Table – This table shows all thirty-one intelligent input functions at a glance.
Detailed description of these functions, related parameters and settings, and example wiring diagrams
are in “Using Intelligent Input Terminals” on page 30.
IIIInput Function Summary Table nput Function Summary Table nput Function Summary Table nput Function Summary Table
O O O Option ption ption ption
C C C Code ode ode ode
T T T Terminal erminal erminal erminal
S S S Symbol ymbol ymbol ymbol
F
F F
Function Name
unction Name unction Name
unction Name D
D D
Descr
escr escr
escription
iption iption
iption
00 00 00 00
FW FORWARD Run/Stop
ON Inverter is in Run Mode, motor runs forward
OFF Inverter is in Stop Mode, motor stops
0 0 0 01 1 1 1
RV Reverse Run/Stop
ON Inverter is in Run Mode, motor runs reverse
OFF Inverter is in Stop Mode, motor stops
0 0 0 02 2 2 2
CF1
Multi-speed Select,
Bit 0 (LSB)
ON Binary encoded speed select, Bit 0, logical 1
OFF Binary encoded speed select, Bit 0, logical 0
0 0 0 03 3 3 3
CF2
Multi-speed Select,
Bit 1
ON Binary encoded speed select, Bit 1, logical 1
OFF Binary encoded speed select, Bit 1, logical 0
0 0 0 04 4 4 4
CF3
Multi-speed Select,
Bit 2
ON Binary encoded speed select, Bit 2, logical 1
OFF Binary encoded speed select, Bit 2, logical 0
0 0 0 05 5 5 5
CF4
Multi-speed Select,
Bit 3 (MSB) ON Binary encoded speed select, Bit 3, logical 1
OFF Binary encoded speed select, Bit 3, logical 0
0 0 0 06 6 6 6
JG Jogging
ON
Inverter is in Run Mode, output to motor runs at
jog parameter frequency
OFF Inverter is in Stop Mode
0 0 0 07 7 7 7
DB External DC braking
ON DC braking will be applied during deceleration
OFF DC braking will not be applied
0 0 0 08 8 8 8
SET
Set (select) 2nd Motor
Data
ON
The inverter uses 2nd motor parameters for
generating frequency output to motor
OFF
The inverter uses 1st (main) motor parameters
for generating frequency output to motor
0
0 0
09
9 9
9
2CH
2-stage Acceleration and
Deceleration
ON
Frequency output uses 2nd-stage acceleration
and deceleration values
OFF
Frequency output uses standard acceleration
and deceleration values
11 11 11 11
FRS Free-run Stop
ON
Causes output to turn OFF, allowing motor to
free run (coast) to stop
OFF
Output operates normally, so controlled
deceleration stop motor
1 1 1 12 2 2 2
EXT External Trip
ON
When assigned input transitions OFF to ON,
inverter latches trip event and displays
E E E E 1 1 1 12 2 2 2
OFF
No trip event for ON to OFF, any recorded trip
events remain in history until reset
1
1 1
13
3 3
3
USP
Unattended Start
Protection
ON
On powerup, the inverter will not resume a Run
command (mostly used in the US)
OFF
On powerup, the inverter will resume a Run
command that was active before power loss
1 1 1 14 4 4 4
CS
Commercial power
source switchover
ON Motor can be driven by commercial power
OFF Motor is driven via the inverter
1
1 1
15
5 5
5
SFT Software Lock
ON
The keypad and remote programming devices
are prevented from changing parameters
OFF The parameters may be edited and stored
1 1 1 16 6 6 6
AT
Analog Input
Voltage/Current Select
ON
Refer to “Analog Input Operation” on page 45.
OFF
1
1 1
18
8 8
8
RS Reset Inverter
ON
The trip condition is reset, the motor output is
turned OFF, and powerup reset is asserted
OFF Normal power-ON operation
1
1 1
19
9 9
9
PTC
PTC thermistor Thermal
Protection
(C005 only)
ANLG
When a thermistor is connected to terminal [5]
and
[L], the inverter checks for
over-temperature and will cause trip event and
turn OFF output to motor
OPEN
A disconnect of the thermistor causes a trip
event, and the inverter turns OFF the motor