Hitachi WJ200-001L, Instruction Manual

Page: 651 / 680

Ver.3
−
− −
−
142
IIIInput Function Summary Table
nput Function Summary Table nput Function Summary Table
nput Function Summary Table
O
O O
Option
ption ption
ption
C C C Code ode ode ode
T
T T
Terminal
erminal erminal
erminal
S S S Symbol ymbol ymbol ymbol
F F F Function Name unction Name unction Name unction Name D D D Descr escr escr escription iption iption iption
2
2 2
20
0 0
0
STA
Start
(3-wire interface) ON Starts the motor rotation
OFF No change to present motor status
2
2 2
21
1 1
1
STP
Stop
(3-wire interface) ON Stops the motor rotation
OFF No change to present motor status
22 22 22 22
F/R
FWD, REV
(3-wire interface)
ON
Selects the direction of motor rotation: ON =
FWD. While the motor is rotating, a change of
F/R will start a deceleration, followed by a
change in direction
OFF
Selects the direction of motor rotation: OFF =
REV. While the motor is rotating, a change of
F/R will start a deceleration, followed by a
change in direction
23
23 23
23
PID PID Disable
ON
Temporarily disables PID loop control. Inverter
output turns OFF as long as PID Enable is
active (A
A A A0 0 0 07 7 7 71 1 1 1=0 0 0 01 1 1 1)
OFF
Has no effect on PID loop operation, which
operates normally if PID Enable is active
(A
A A
A0
0 0
07
7 7
71
1 1
1=0
0 0
01
1 1
1)
24 24 24 24
PIDC PID Reset
ON
Resets the PID loop controller. The main
consequence is that the integrator sum is forced
to zero
OFF No effect on PID controller
2 2 2 27 7 7 7
UP
Remote Control UP
Function (motorized
speed pot.)
ON
Accelerates (increases output frequency) motor
from current frequency
OFF Output to motor operates normally
2 2 2 28 8 8 8
DWN
Remote Control Down
Function (motorized
speed pot.)
ON
Decelerates (decreases output frequency) motor
from current frequency
OFF Output to motor operates normally
2
2 2
29
9 9
9
UDC
Remote Control Data
Clearing ON
Clears the UP/DWN frequency memory by
forcing it to equal the set frequency parameter
F001. Setting C
C C C1 1 1 10 0 0 01 1 1 1 must be set=00 00 00 00 to enable
this function to work
OFF UP/DWN frequency memory is not changed
3 3 3 31 1 1 1
OPE Operator Control
ON
Forces the source of the output frequency setting
A
A A A00 00 00 001 1 1 1 and the source of the Run command A A A A00 00 00 002 2 2 2
to be from the digital operator
OFF
Source of output frequency set by A
A A
A00
00 00
001
1 1
1 and
source of Run command set by A A A A00 00 00 002 2 2 2 is used
32 32 32 32
SF1
Multi-speed Select,
Bit operation Bit 1 ON Bit encoded speed select, Bit 1, logical 1
OFF Bit encoded speed select, Bit 1, logical 0
33 33 33 33
SF2
Multi-speed Select,
Bit operation Bit 2 ON Bit encoded speed select, Bit 2, logical 1
OFF Bit encoded speed select, Bit 2, logical 0
34 34 34 34
SF3
Multi-speed Select,
Bit operation Bit 3
ON Bit encoded speed select, Bit 3, logical 1
OFF Bit encoded speed select, Bit 3, logical 0
35 35 35 35
SF4
Multi-speed Select,
Bit operation Bit 4
ON Bit encoded speed select, Bit 4, logical 1
OFF Bit encoded speed select, Bit 4, logical 0
3 3 3 36 6 6 6
SF5
Multi-speed Select,
Bit operation Bit 5
ON Bit encoded speed select, Bit 5, logical 1
OFF Bit encoded speed select, Bit 5, logical 0
3 3 3 37 7 7 7
SF6
Multi-speed Select,
Bit operation Bit 6
ON Bit encoded speed select, Bit 6, logical 1
OFF Bit encoded speed select, Bit 6, logical 0
3 3 3 38 8 8 8
SF7
Multi-speed Select,
Bit operation Bit 7
ON Bit encoded speed select, Bit 7, logical 1
OFF Bit encoded speed select, Bit 7, logical 0
3 3 3 39 9 9 9
OLR
Overload Restriction
Source Changeover
ON Perform overload restriction
OFF Normal operation