Hitachi WJ200-001L, Instruction Manual, Page: 32 / 680

1
− − − −
9
Item General Specifications
Output
signal
Intelligent output
terminal
48 functions assignable
RUN
RUN RUN
RUN (run signal), FA1~FA5
FA1~FA5 FA1~FA5
FA1~FA5 (frequency arrival signal), OL,OL2
OL,OL2 OL,OL2
OL,OL2 (overload
advance notice signal), OD OD OD OD (PID deviation error signal), AL AL AL AL (alarm signal),
OTQ OTQ OTQ OTQ (over/under torque threshold), UV UV UV UV (under-voltage), TRQ TRQ TRQ TRQ (torque limit
signal), RNT
RNT RNT
RNT (run time expired), ONT
ONT ONT
ONT (power ON time expired), THM
THM THM
THM
(thermal warning), BRK
BRK BRK
BRK (brake release), BER
BER BER
BER (brake error), ZS
ZS ZS
ZS (0Hz
detection), DSE DSE DSE DSE (speed deviation excessive), POK POK POK POK (positioning completion),
ODc ODc ODc ODc (analog voltage input disconnection), OIDc OIDc OIDc OIDc (analog current input
disconnection), FBV
FBV FBV
FBV (PID second stage output), NDc
NDc NDc
NDc (network disconnect
detection), LOG1~LOG3
LOG1~LOG3 LOG1~LOG3
LOG1~LOG3 (Logic output signals), WAC
WAC WAC
WAC (capacitor life
warning), WAF WAF WAF WAF (cooling fan warning), FR FR FR FR (starting contact), OHF OHF OHF OHF (heat sink
overheat warning), LOC LOC LOC LOC (Low load), MO1~MO3 MO1~MO3 MO1~MO3 MO1~MO3 (general outputs for EzSQ),
IRDY
IRDY IRDY
IRDY (inverter ready), FWR
FWR FWR
FWR (forward operation), RVR
RVR RVR
RVR (reverse operation),
MJA MJA MJA MJA (major failure), WCO WCO WCO WCO (window comparator O), WCOI WCOI WCOI WCOI (window
comparator OI), FREF FREF FREF FREF (frequency command source), REF REF REF REF (run command
source), SETM
SETM SETM
SETM (second motor in operation), EDM
EDM EDM
EDM (STO (safe torque off)
performance monitor), OP
OP OP
OP (option control signal), NO
NO NO
NO (no function)
Monitor output (analog) Output freq., output current, output torque, output voltage, input power,
thermal load ratio, LAD freq., heat sink temperature, general output (EzSQ)
Pulse train output
(0~10Vdc, 32kHz max.) [PWM output] [PWM output] [PWM output] [PWM output]
Output freq., output current, output torque, output voltage, input power,
thermal load ratio, LAD freq., heat sink temperature, general output (EzSQ)
[Pulse train output]
[Pulse train output] [Pulse train output]
[Pulse train output]
Output frequency, output current, pulse train input monitor
Alarm output contact ON for inverter alarm (1c contacts, both normally open or closed available.)
Other functions Free-V/f, manual/automatic torque boost, output voltage gain adjustment,
AVR function, reduced voltage start, motor data selection, auto-tuning,
motor stabilization control, reverse running protection, simple position
control, simple torque control, torque limiting, automatic carrier frequency
reduction, energy saving operation, PID function, non-stop operation at
instantaneous power failure, brake control, DC injection braking, dynamic
braking (BRD), frequency upper and lower limiters, jump frequencies, curve
accel and decel (S, U, inversed U,EL-S), 16-stage speed profile, fine
adjustment of start frequency, accel and decel stop, process jogging,
frequency calculation, frequency addition, 2-stage accel/decel, stop mode
selection, start/end freq., analog input filter, window comparators, input
terminal response time, output signal delay/hold function, rotation direction
restriction, stop key selection, software lock, safe stop function, scaling
function, display restriction, password function, user parameter,
initialization, initial display selection, cooling fan control, warning, trip
retry, frequency pull-in restart, frequency matching, overload restriction,
over current restriction, DC bus voltage AVR
Protective function Over-current, over-voltage, under-voltage, overload, brake resistor overload,
CPU error, memory error, external trip, USP error, ground fault detection at
power on, temperature error, internal communication error, driver error,
thermistor error, brake error, safe stop, overload at low speed, modbus
communication error, option error, encoder disconnection, speed excessive,
EzSQ command error, EzSQ nesting error, EzSQ execution error, EzSQ user
trip
Operating
environment Temperature Operating (ambient): -10 to 40
°
C(*10), / Storage: -20 to 65
°
C(*11)
Humidity
20 to 90% humidity (non-condensing)
Vibration *11 5.9m/s
2
(0.6G), 10 to 55 Hz
Location
Altitude 1,000m or less, indoors (no corrosive gasses or dust)
Coating color Black
Options
Remote operator unit, cables for the units, braking unit, braking resistor, AC
reactor, DC reactor, EMC filter, fieldbus