Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 97

Page: 97 / 427

GL-10x0

Administrator’s Guide

Log in as the Administrator

At the top right-hand corner of the TopAccess window, click

Login

The Login page opens.

TopAccess Login Page

Enter the administrator user name and password.
This is the same password used at the LCD touch screen to log in for

administrative functions.
The default administrator user name is “Admin” and the default

password is

“

12345”.

If you have not set the user name and password, use the defaults and

change the password immediately to maintain secure access.
For instructions on setting the administrator password, see

Setting

the Administrator Password

on page 66.

To cancel the login process click

Cancel

TopAccess returns you to the page you came from.

Note: Clicking

Login

with an invalid password (or no password while a

password has been set) causes the message “Invalid Password” to

display in the Login page. You can then either click

Cancel

to cancel

the login or log in again with a valid password.

Logging Out

To log out, click the

Logout

link in the top, right-hand corner of the

TopAccess window.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 97 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: