Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 197

Page: 197 / 427

GL-10x0

Administrator’s Guide

175

LPR/LPD Printing

Considerations and Limitations

You must add and configure Microsoft TCP/IP printing services from

the Network folder in the Windows Control Panel before you can add

an LPR printer port (Windows NT, Windows 2000, and Windows XP

only).

To print a file using the LPR command line, the file must be in an

encapsulated print format or a standard text file.

Prerequisites

Install Microsoft TCP/IP Printing Services.

Add an LPR port.

Configuring Microsoft LPD Printing

Launch your Web browser.

Open TopAccess using the IP address of the controller you want to

configure. (Refer to

Opening TopAccess

on page 72.)

Note: You can find the IP address through TopAccessDocMon.

Click the Administration tab.

Click the Setup submenu.

Click the

Print Services

link.

In the

LPD Printing

text box, select

Enable

from the drop-down list.

Scroll down to the bottom of the page and click

Save

Proceed to

Installing Client Software

on page 229.

All these procedures are described in detail in the

Operator’s Guide

IPP Printing

Considerations and Limitations

If you configure the controller as an IPP-compatible printer, end-users

can print to the device over the Internet. IPP printing is available only over

TCP/IP.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 197 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: