Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 136

Page: 136 / 427

114

GL-10x0

Administrator’s Guide

Although you set the protocols during the installation process, you can

improve network performance by customizing the settings for your

particular network configuration. For example, the default method for

acquiring the controller IP Address is through DHCP. If your controller

operates in a NetWare environment (IPX), this default setting generates

unnecessary TCP/IP traffic.
You must log in as an administrator to set network protocol properties.

Enabling/Disabling the Ethernet NIC

Disabling the ethernet NIC disables the wired network path for the

controller and digital copier. If you have set up a wireless network, you

can still use the network-related functions of the controller. If you do not

have a functioning network connection, you can only use the device for

walk-up functions.
1

On the Administration tab, click the

Setup

subtab.

Click the

Network

link. The Network page opens.

In the Device area, click the

Network Card

drop-down list.

Select

Enable

Disable

Click

Save

If you change the TCP/IP protocol settings or enable/disable a

network card, you must reboot the controller before the changes take

effect.
For information on rebooting the controller, see

Rebooting the

Controller

on page 43.

Configuring Ethernet NIC Speed

The ethernet NIC speed is set to

Auto

by default. If you use a consistent

speed for all networked devices and transactions, you can set the speed

specifically. You may also want to set the speed manually if you are

experiencing speed-related network errors.
1

On the Administration tab, click the

Setup

subtab.

Click the

Network

link. The Network page opens.

In the Ethernet area, click the

Speed

drop-down list.

Select the appropriate speed for the controller NIC. The default setting

Auto

, which automatically senses and sets the correct speed.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 136 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: