manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 53 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 53

GL-10x0 Administrator’s Guide

31

Configuring the Ethernet Speed Settings

1

From the Network Setting menu, press 

ETHERNET

 to open the Ethernet 

Setting screen.

Ethernet Setting Screen

2

Set the network speed to 

10 

MB

/

S

 or 

100 

MB

/

S

. Alternatively, select 

AUTO

 

to automatically sense and set the correct speed.

3

Press 

OK

 to save your setting.

Configuring AppleTalk Protocol Settings

1

From the Network Setting menu, press 

APPLETALK

 to open the 

AppleTalk Setting screen.

AppleTalk Setting Screen

Note: Currently, the controller supports EtherTalk access only; 

TokenTalk is not supported.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments