manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 208 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 208

186

 GL-10x0 Administrator’s Guide

Hole Punching

When the hole punch option is installed it can be activated using the 

following options.

If this option is not specified, the default value of 

nopunch

 is used.

This function is not available for all paper sizes and users should refer to 

the copier manual for a list of compatible paper sizes.  In particular, A5, 

A6, and statement paper sizes do not support this function.
Example: The command to hole punch the long edge feed portrait page is 

lp –o punch=1  <filename>

.

Media Type

You can select the paper source and the media type using the following 

options.

Hole Punch Options

Option Value Alternate Value

Description

punch=0

nopunch

Hole punching is turned off.

punch=1

Hole punch long edge without rotation.

punch=2

Hole punch short edge without rotation.

punch=3

Hole punch long edge with 180° rotation.

punch=4

Hole punch short edge with 180° rotation.

Media Type Options

Option Value Description

Plain

The paper source that contains 

plain paper

 is requested.

Transparency

The paper source that contains 

transparency slides 

is requested.

Tab

The paper source that contains 

tab paper 

is requested.

Thick1

The paper source that contains 

disk labels

 is requested.

Thick2

The paper source that contains 

letter labels

 is requested.

Cover

The paper source that contains 

cover paper

 is requested.

Insert

The paper source that contains 

insert paper

 is requested.

Special

The paper source that contains 

special paper

 is requested.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments