Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 49

Page: 49 / 427

GL-10x0 Administrator’s Guide

Press

NETWORK

SETTING

The Network Setting screen opens.

Network Setting Screen

To access specific protocol settings, press the applicable soft key.
For more details, refer to the following pages in this manual:

TCP/IP server (see

Configuring TCP/IP Protocol Settings

page 28)

WINS server (see

Setting Up WINS and DNS Servers

page 29)

IPX/SPX (see

Configuring IPX/SPX Protocol Settings

page 29)

Ethernet speed (see

Configuring the Ethernet Speed Settings

on page 31) only for Ethernet

AppleTalk (see

Configuring AppleTalk Protocol Settings

page 31) only for Ethernet

After you finish updating network or device settings, you must apply the

changes you made during the session. This process updates and reboots

the controller so the modifications can take effect. If you do not apply

your changes, they are lost when you press

COPY

or the copier times out.

Note: Check the configuration page that automatically prints upon

start up to confirm that the changes were applied.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 49 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: