Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 37

Page: 37 / 427

GL-10x0 Administrator’s Guide

Select the

TOSHIBA e-STUDIO GL-Fax and Address Book

component and then

click

Add/Remove

. The Setup Options menu opens:

The Setup Options Menu

Click

Remove

. This option removes all installed TOSHIBA GL Fax

Driver software from your system.

Click

Next

to proceed.

You are prompted to confirm the removal. To quit without removing

the software, click

Cancel

. Otherwise, click

to continue.

You must restart your computer for the un-installation process to

complete. Select whether the restart now or later and then click

Finish

Uninstallation is complete.

Configuring Fax Properties

After installing the fax driver, you may want to configure the fax

properties. This section provides an overview of the driver options you can

set. For more detail on using the fax driver, refer to the

Network Fax

Operator’s Guide.

From the Windows Printer Folder, right-click on the GL Fax Driver

printer icon.

Choose

Properties

from the short-cut menu. The GL Fax Driver

properties are grouped on a tabbed dialog box, from which you can

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 37 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: