Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 183

Page: 183 / 427

GL-10x0

Administrator’s Guide

161

Open TopAccess using the IP address of the controller you want to

configure. (Refer to

Opening TopAccess

on page 72.)

Note: You can find the IP address through TopAccessDocMon.

Click the Administration tab.

Click the Setup tab.

Click the

Network

link.

Setup Page

From the IPX/SPX settings group, select the

Enable

protocol option.

Select the applicable

Frame Type

. Accept the default,

Auto

, to

automatically sense the

Frame Type

Continue with

Set Print Services

on page 161.

Set Print Services

On the Setup tab, click the

Print Services

link.

From the

Service

drop-down list, select

Enable

From the

Operating Mode

drop-down list, select

Print Server

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 183 / 427

Search results

Summary of Contents for e-STUDIO GL-1010

Reviews: