manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 320 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 320

298

 GL-10x0 Administrator’s Guide

Network Connectivity Problems

Problem Description

There are many variables within a network environment that make 

installing an integrated device challenging. The easiest environment in 

which to install the controller is over TCP/IP using a DHCP server to 

dynamically assign and resolve IP addresses between devices.
Using the default configuration settings also assures an easier 

implementation. However, you may need to customize the settings to 

accommodate your network environment.
Some common network configuration options are shown below, with the 

steps required to configure a controller in each. If you perform all the 

steps in the applicable checklist and still cannot print satisfactorily to the 

controller, contact your TOSHIBA authorized dealer for further 

assistance.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments