manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Administrator'S Manual, Page: 219 / 427

Share
Download
Toshiba e-STUDIO GL-1010 Administrator'S Manual Download Page 219

GL-10x0 Administrator’s Guide

197

If the right margin is set to the left of the left margin or if it is set to a 

position wider than the logical page it is ignored. The right margin is 

specified in columns from the left margin. A negative value is ignored.
If this option is not specified, the default value is used.
Example: The command to set the right margin to fifty columns is 

lp –o 

rm=50  <filename>

.

Top Margin

Specify the top margin position with the following option.

If the top margin is set too high or too low, part of the text may not appear 

because of the printer-specific unprintable region. The top margin is 

ignored if it is set to a value greater than the logical page length. Setting 

this value may affect the number of lines specified using the page length 

option.
If this option is not specified, the default value is used.
Example: The command to set the top margin to ten lines is 

lp –o tm=10  

<filename>

.

Paper Source

Specify the current paper source using the following options.

Top Margin Option

Option Value

Description

tm=

value

Set the top margin to 

value

 lines.

Paper Source Options

Option Value Alternate Value Description

auto-source

Select auto paper tray selection.

manual

Select the manual/bypass paper tray.

upper

cas1

Select the upper paper tray.

lower

cas2

Select the lower paper tray.

tandem

Select the tandem LCF paper tray.

external

Select the external paper tray.

pedupper

cas3

Select the pedestal upper paper tray.

pedlower

cas4

Select the pedestal lower paper tray.

Summary of Contents for e-STUDIO GL-1010












































































































































































































































































































































































































































Reviews:

No comments